ATCOM MP01 Guide d'installation

MP01 Administrator Manual Version: V1.0 2010-12-27

9 iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface wlan0 -j ACCEPT echo 1 &

10 [general] register=6015:[email protected] [6015]

11 OCTET_B=`uci show network.wifi0.ipaddr | cut -d = -f2 | cut -d . -f2` OCTET_C=`uci show network.wifi0.ipaddr | cut -d = -f2 | cut -d . -f3` OCTET

12 ln -s /etc/init.d/udhcpd /etc/rc.d/S99udhcpd ln -s /etc/init.d/batmand /etc/rc.d/S90batmand ln -s /etc/init.d/create-batman-status-page.sh /et

13 The first screen that appears is the Mesh Potato GUI (shown as below). You can preview the MP01 settings and set up the WiFi network, wireless, B

14 OpenWrt GUI Overview => User Interface You can customize the settings and the functionality of LuCI on User Interface.

15 User Interface Overview => LuCI Components The LuCI Components screen shows the package list. Here you can download and install package, and

16 LuCI Components Overview => Logout Logout OpenWrt GUI. Status => Interfaces The Interfaces screen displays the interface status, such as D

17 Interfaces Status => Firewall The Firewall screen shows the firewall configurations. Every rules you have set up for firewall will be shown h

18 Firewall Status => Active Connections The Active Connections page gives an overview over currently active network connections.

1 Table of Contens Contact ATCOM ...

19 Active Connectios Status => Routes This page shows the active routes. Routes Status => System Log This page shows the system logs.

20 System Log Status => Kernel Log This page shows the kernel logs. Kernel Log System => System Here you can configure the basic aspects of

21 System System => Software This page will show you the softwares you have installed or not installed. You can download and install the package

22 System => Admin Password You can change the password of the system administrator here. Admin Password System => SSH-Keys You can paste pub

23 Processes System => Mount Points This page displays the mounted file systems, mount points and swap device. Mount points define at which poin

24 Mount Points System => LED Configuration You can customizes the behavior of the device LEDs if possible. Just add an entry, choose the LED de

25 LED Configuration LED Name: Enter the LED name you like LED Device: Choose which LED you want to twinkle Default state: The default state of the

26 Backup / Restore System => Flash Firmware This feature allows you to upload an OpenWrt image file to reflash the device. Flash Firmware Syst

27 Reboot Services => Busybox HTTPd It is a small web server which can be used to serve LuCI. You can configure the server port and document roo

28 Dropbear SSHd Services => Dnsmasq Dnsmasq is a lightweight, easy to configure DNS forwarder and DHCP server. It is designed to provide DNS an

2 Contact ATCOM The Introduction of ATCOM Founded in 1998, ATCOM technology has been always endeavoring in the R&D and manufacturing of the inte

29 Dnsmasq Services => Scheduled Tasks This is the system crontab in which scheduled tasks can be defined. You can edit the configuration file o

30 Scheduled Tasks Network => Interfaces => WIFI0 / LAN On this page you can configure the network interfaces. You can bridge several interfa

31 Interfaces => WIFI0

32 Interfaces => LAN Network => Wifi Here you can scan the WiFi networks in your local environment. The following screen shows the WiFi netwo

33 Wifi Network => Wifi => WIFI0 You can run several wifi networks with one device. Be aware that there are certain hardware and driverspec

34 Wifi => WIFI0 Enable: To make WiFi available or not. Channel: It has 11 WiFi channels to choose. Mode: MP01 supports 802.11b/g ESSID/BSSID: W

35 Switch Network => DHCP You need to install the dnsmasq package before using it. You can configure the DHCP options such as assigned range, le

36 Start: The first IP address it will assign Limit: The last IP address it will assign Leasetime: The amount of time a network user will be allowed

37 4. Troubleshooting 4.1 What to do if you can’t connect to the MP anymore - using the Fallback-IP This can easily happen if you are mess

38 -- Called [email protected] -- event_onhook -- default: hangup sound_on = 1 == Spawn extension (default, 142, 1) exited non-zer

3 MP01 Administrator Manual This document describes detailed information for the MP01, and it will guide you through the installation for setting up

39 RedBoot 0xA8000000 0xA8000000 0x00030000 0x00000000 rootfs 0xA8030000 0xA8030000 0x006F0000 0x00000000 vmlinux.bin.l7 0xA8720000 0x80041000 0x000

40 Telephone Line (PoTL) Open Hardware Design No vendor lock-in. Open to improvement by anyone. Open Source firmware Linux, OpenWRT, B.A.T.M.A.N., a

41 Physical  Casing: UV-protected, weatherproof outdoor enclosure  Mounting: Pole Mount/Wall Mount  Enclosure Size: 228 X 106 X 55 mm  Weigh

4 1.3 Server Only one computer is required to provide the services for the Telco system. This computer, called the VT Server, could be anything fro

5 Accounting. A3Glue This is the glue, making Afrimesh, A2billing and the Mesh network work together. It gathers data from the network, provi

6 In this network topology, all the MP01 is an extension and act as mesh node also. And VT Server is installed Afrimesh and act as a visualization

7 sudo apt-add-repository ppa:afrimesh/ppa sudo apt-get update 2) Install supporting packages sudo apt-get install batmand polipo villagetelco-dashb

8 If you haven't already set the password on the MP01, do that now by telneting to 192.168.1.20 and issuing the „passwd‟ command. This will ena